Barnstead D11911 Especificações

BARNSTEAD|THERMOLYNENANOpure®DIamond™UVultrapure water systemOperation ManualSeries 1191Model No. VoltageD11911 100V - 240VLT1191X1 • 6/22/00

Other AccessoriesOptional accessories for this unit include a float switch,low pressure switch, N.I.S.T. Traceable CalibrationModule, remote dispenser

UV Lamp InstallationLocate the UV chamber inside the left door of theNANOpure DIamond UV. Install the UV Lamp as follows:1. Disconnect the power cord

Bench Mounting1. Place the NANOpure DIamond UV on a benchtop that is accessible to pretreated water, elec-tricity and an atmospherically vented drain.

Installing the Control Panel in aRemote LocationFor your convenience, the control panel can be removedfrom the unit and mounted at a convenient locati

14Water ConnectionsFeed Water Connection1. Locate the length of 3/8” (.95 cm) O.D. tubingprovided with the unit with a quick disconnectinsert on one e

15Main Power SwitchThe main power switch on the NANOpure DIamond UV islocated on the lower back right side of the unit (as youface the front of the un

SwitchesWhen the main power switch (on the lower back right sideof the unit as you face the unit) is ON, the switches onthe control panel function as

17Cartridge packs will come bagged with four manifold connection caps.Part ApplicationDIamond Kit Organic Free R/O & Distilled FeedD50280 Ultra-Lo

18Initial Rinse1. Attach the feed water line to the unit by snapping the quick disconnect coupling into the quick disconnect body in the lower left ba

19System Sanitization ProcedureYour NANOpure DIamond UV has been shipped with acleaning syringe (Cat. No. CMX25). When the system isnew or whenever a

Safety Information ...

20and press ENTER. Display will now read, “UnitSanitizing.”14. Unit may now be left unattended until displayreads, “Sanitization Complete: Press ENTER

211. Turn the system power ON by depressing themain power switch to the “I” position.2 The system greeting display indicates the typeof unit you own.

Adjusting Display Brightness1. From the (Idle) mode, when the display reads,“NANOpure Diamond (Idle) xx:xx:xxxx/xx/xx,” press the UP or DOWN arrow unt

232. Press ENTER.3. Press ENTER when the unit displays “PrinterAttached?”4. When prompted with “Date Format” press theUP or DOWN arrow to show the dat

242. Unlatch and open the right side door.3. Find and copy down the two cell constantsattached to the gray cable, leaving the electron-ics board mount

25Use of Standby ModeAt the end of the work day, place the NANOpureDIamond UV in Standby mode for the night. To place theunit in Standby mode:1. From

267. Press ENTER.8. Press BACK to return to the (Idle) mode.The second line of the display will show a “Below Setpoint” message once every 8 to 10 sec

27USER SETTINGS3. Press the UP or DOWN arrow to select “Yes.”4. Press ENTER and the timer will be reset forapproximately five months of operational ti

28NotePress the STOP/STOP switch to can-cel the flush.Setting Timed Dispensing1. From the normal recirculating mode, when the dis-play is showing puri

292. Press the UP or DOWN arrow to select “MΩ-cm”or “uS/cm” Press ENTER.3. Press BACK to return to the normal recirculatingmode.Temperature Compensati

Your Barnstead|Thermolyne NANOpure DIamond UVultrapure water system has been designed with function,reliability, and safety in mind. It is your respon

30Accessories D8964 (float switch) and D2706 (pressureswitch) are designed to protect the NANOpure DIamondUV pump by alerting the system of an inadequ

31Performing an ElectronicCalibration Using the OptionalN.I.S.T. Calibration ModuleIf you purchased the optional N.I.S.T. calibration module(Catalog N

32N.I.S.T. CALIBRATION MODULE11. Press BACK to return to the (Idle) mode.12. Turn the main power switch to the OFF “O” position. Unplug the unit.13. R

Connecting NANOpureDIamond to Computer andCommunicating Though the RS-232 Port UsingHyperterminal or ProcommHyperterminal RS-232 Capture Instructions1

34capture text. Accepting default will put the filewhich you name in the c:/windows directorycalled capture.txt and the file will be an ASCIItext file

3512. Type in 21 <Enter>, sets to COM2: or (Type in20 <Enter>, sets to COM1:), depending on yourcomputer.13. Type in 24 <Enter>, sav

367. From the “Printer Attached” display, press theUp or DOWN arrow for (YES).8. Press ENTER. Press BACK twice to return tothe (Idle) mode.9. During n

37down; or—the paper may be jammed in the printer. Turnthe printer OFF before checking for jammed paper.Remove the paper jam and turn the printer back

38General Cleaning InstructionsDisconnect electrical service to the unit. Wipe exteriorsurfaces with lightly dampened cloth containing mild soapsoluti

System SanitizationAfter sanitization is complete (approximately 3.5 hours),place the unit into its normal (recirculation) mode to allowthe system to

3. Avoid splashing disinfecting solutions on clothing or skin.4. Ensure all piping connections are tight to avoidchemical leakage.5. Ensure adequate v

4014. Unit may now be left unattended until the display reads, “Sanitization Complete: PressENTER.”15. After sanitization is complete and the userpres

41Cartridge Pack ReplacementThe frequency with which you will need to clean your unitand replace your cartridge pack is dependent on yourfeed water’s

0.2 Micron Filter ReplacementReplace the 0.2 micron final filter whenever any of the fol-lowing conditions occur: every 30 days, the product waterflow

43UV Lamp ReplacementThe ultraviolet lamp requires changing every 5-6 months.Lamp Life will vary according to the number of times theNANOpure DIamond

446. Make sure the UV lamp cable is tucked behindthe chamber before closing and relatching thedoor.7. Reconnect power cord and turn unit ON.8. Reset U

45Problem Possible Causes SolutionsNANOpure DIamond completely No electrical power to NANOpure Ensure NANOpure DIamond power inactive (pump and displ

46Poor quality feed water. If a Barnstead ROpure is the feed water source, check that the membrane is functioning properly.If a Barnstead Still is the

47Display reads, “Meter PC board communication error. Turn the NANOpure DIamond OFFBoard Problem.” (I/O Switch) and restart the unit.System electronic

48Recommended SparesConsumablesConsumable parts are those required to support the day-to-day operation of this equipment.Barnstead|Thermolyne establis

49Safety StockFor critical applications where performance with minimum downtime is required, Barnstead|Thermolyne rec-ommends that you maintain a loca

Congratulations on your purchase of a Barnstead|Thermolyne NANOpure DIamond UV ultrapure water sys-tem. This water purification system is designed to

50Flow ChartUnit Initialization & MeterCalibration CheckNANOpure DIamond (Idle)xx :xx:xx xx /xx/xxstart_stopkey pressedup or downkeys pressedSani

51Wiring DiagramCONNECTORREMOTE DISPLAYCSW1190X2SW1190X2SW1190X2(SPG)230V: (2) FSX54& FUSES:120V: (2) FSX47& D11931 ONLYMODEL #s D11911 LINENE

52Ordering ProceduresPlease refer to the Specification Plate located inside theleft side door for the complete model number, serial num-ber, and serie

53Barnstead|Thermolyne Corporation warrants that if a product manufactured by Barnstead|Thermolyne andsold by it within the continental United States

54

55

9001ISOREGISTEREDBarnstead|Thermolyne2555 Kerper Blvd.P.O. Box 797Dubuque, IA 52004-2241Phone: 319-556-2241 800-553-0039Fax: 319-589-0516E-Mail Addr

Dimensions and Clearance RequirementsDimensions 13.4” W x 19.5” H x 16.9” D (34.0 x 49.5 x 42.8 cm)ClearancesSides - 9” (22.9 cm) minimum for servicin

Environmental Conditions Operating: 4°C - 49°C; 20% to 80% relative humidity, non-condensing. Installation Category II (over-voltage) in accordance w

1. Remove the unit from its shipping container.Remove all contents carefully. Ensure that theUV lamp, feed and drain tubing, sanitizationcartridge, w

9Choosing a SiteThe NANOpure DIamond UV features a removable con-trol panel display which allows the system to be mountedalmost anywhere within the la